MTM Power GmbH

Address:
Zirkel 3
Schwarzatal
98744
Germany

Phone: +49 69 1 54 26-0

Fax: +49 69 1 54 26 20

Web: www.mtm-power.com


MTM Power GmbH articles

Displaying 1 - 11 of 11

DC/DC converters with 14W designed for railway applications

DC/DC converters with 14W designed for railway applications
The DC/DC converters of the series PMGS/PCMGS14 from MTM Power have been designed for transport and railway applications where low-ranged power is needed. The devices operate at a nominal input voltage of 72VDC or 110VDC and supply an output voltage of 24VDC (12VDC and 48VDC on request) with a high efficiency of more than 90%.
13th April 2018

DC/DC converters designed for vehicle and rail applications

DC/DC converters designed for vehicle and rail applications
Specially designed for applications in vehicle and rail technology, MTM Power has introduced the primary switched DC/DC converters PCMDS150WK-IP65, which are also for use in industrial and telecommunication applications. The push-pull topology used while developing these converters enables a wide input voltage range with high efficiency. Thus the 150W converters are available with a wide input range for battery voltages of 24, 36, 48, 60, 72, 80, 96 and 110V.
31st January 2018

DC/DC converters designed for automotive applications

DC/DC converters designed for automotive applications
A range of primary switched DC/DC converters with 400W output power has been released by MTM Power, especially designed for automotive applications. They operate according to the push-pull principle; i. e. the input DC voltage is chopped by two push-pull working transistors with a frequency of approximately 60kHz. 
23rd January 2017


14W DC/DC converters suit railway applications

14W DC/DC converters suit railway applications
The DC/DC converters of the PMGS/PCMGS14 series from MTM Power have been designed for transport and railway applications where low-ranged power is needed. The devices operate at a nominal input voltage of 72 or 110VDC and supply an output voltage of 24VDC (12 and 48VDC on request) with a high efficiency of over 90 %. The PMGS/PCMGS14 are available with an input reverse polarity protection by a series diode and are continuous short circuit protected.
12th July 2016

DC/DC converters for IP65 applications

DC/DC converters for IP65 applications
MTM Power’s primary switched PCMDS150WK-IP65 DC/DC converters are specially designed for applications in vehicle and rail technology but also for use in industrial and telecommunication applications.
8th February 2016

75W DC/DC converters suit automotive applications

75W DC/DC converters suit automotive applications
MTM Power GmbH, a power supply specialist, has announced its URC series of 75W DC/DC converters for use in automotive applications. They have been designed as power supplies for use in vehicles, particularly for railway applications. The converters are available as a 19" plug-in version, or for wall mounting, both to be connected via a H15 connector, and can be switched on and off by the enable input.
11th June 2015

DC/DC converters suit rail & automotive applications

DC/DC converters suit rail & automotive applications
MTM power has released a set of primary switched DC/DC converters, PCMDS80, designed specifically for applications in rail and automotive, but also suitable for use in industrial and telecomms applications. They are available with 80W output power and operate according to the single transistor forward converter topology with a frequency of 50kHz.
10th March 2015

DC/DC converters target automotive applications

DC/DC converters target automotive applications
Designed for automotive applications, the PCMD400W series of 400W DC/DC converters has been released by MTM Power. A transformer and a secondary linear choke enable a galvanically isolated output voltage of 12 or 24V, which is adjusted by pulse-width modulation according to the current mode principle.
8th December 2014

DC/DC converters have an efficiency of more than 90%

DC/DC converters have an efficiency of more than 90%
  Designed for automotive and railway applications, the PMGS/PCMGS14 series of DC/DC converters has been released by MTM Power. The converters, which are available with a nominal input voltage of 72 or 110VDC, provide an output voltage of 24VDC (12 and 48VDC on request).
22nd September 2014

Converters operate to the current source push-pull principle

Converters operate to the current source push-pull principle
A primary switched DC/DC converters series, specifically designed for automotive and railway applications, has been introduced by MTM Power. The PMDS/PCMDS30 series operate according to the current source push-pull principle and working with a frequency of 70/140 kHz.
23rd May 2014

250W DC/DC converter for railway applications

250W DC/DC converter for railway applications
Suitable for supplying points, signal lamps and electronic monitoring of the rail net, MTM Power has introduced the HVC series 250W DC/DC converters for railway applications. The devices are available with an input range of 420-1100V dc (375-1125V dc for less than 2 seconds), isolation up to 8 kV ac and the standard output voltage of 24V dc.
7th March 2014


Sign up to view our publications

Sign up

Sign up to view our downloads

Sign up

ELIV 2019
16th October 2019
Germany Bonn World Conference Center